...
https://github.com/fjalvingh/tu58fs - branch 1144. A pull request has been added to Jorg’s repo; I need to see if he is willing to accept it.
Checking/setting the TU58 interface’s speed
The speed for the TU58 interface is set on the MFM board (M7096) on switch E7:
...
On my machine they were set as follows:
...
which according to the following table:
...
means it was set to 9600bps.
Preparing for running the emulation
...
so I’m going to assume it’s the same issue (power monitor bit set).
Second round of tests (after switching the PSU)
KKAAB0 (CPU + EIS)
| Code Block |
|---|
END OF CKKAAB0 11/44 CPU/EIS
END OF CKKAAB0 11/44 CPU/EIS
END OF CKKAAB0 11/44 CPU/EIS
END OF CKKAAB0 11/44 CPU/EIS
END OF CKKAAB0 11/44 CPU/EIS
END OF CKKAAB0 11/44 CPU/EIS |
KKABD1 (Traps)
| Code Block |
|---|
CKKABD0 11/44 TRAPS
NO FLOATING POINT OPTION PRESENT
NO CIS OPTION PRESENT
END OF CKKABD0 11/44 TRAPS
END OF CKKABD0 11/44 TRAPS |
KKTAB1 (mmu)
| Code Block |
|---|
CKKTAB 11/44 MEM MGMT PRT A
END PASS # 1 TOTAL ERRORS SINCE LAST REPORT 0
END PASS # 2 TOTAL ERRORS SINCE LAST REPORT 0
END PASS # 3 TOTAL ERRORS SINCE LAST REPORT 0
END PASS # 4 TOTAL ERRORS SINCE LAST REPORT 0
END PASS # 5 TOTAL ERRORS SINCE LAST REPORT 0
END PASS # 6 TOTAL ERRORS SINCE LAST REPORT 0
END PASS # 7 TOTAL ERRORS SINCE LAST REPORT 0 |
KKTBD0 (mmu)
| Code Block |
|---|
CKKTBD0 11/44 MEM MGMT PRT B
EOP MESSAGES WILL PRINT EVERY 64 PASSES OR ABOUT 11 SECONDS
END PASS # 64
END PASS # 128
END PASS # 192 |
KKUAE0 (ubi, map)
| Code Block |
|---|
CKKUAE 11/24/44 UBI MAP
DIAGNOSTIC HAS DETERMINED THAT CPU IS AN 11/44
END PASS # 1
END PASS # 2
END PASS # 3
END PASS # 4
END PASS # 5
END PASS # 6 |
KKKA (Cache)
| Code Block |
|---|
CKKKAC0 11-44 KK11B CACHE
RMI REGISTER (G5179) NOT USED-SKIP HI ORDER BIT ADDRESS TEST
UNIBUS EXERCISER NOT USED- DMA TESTS NOT PERFORMED
END OF PASS # 1
END OF PASS # 2
END OF PASS # 3 |
ZMSP (Memory)
| Code Block |
|---|
CZMSPC MS11-L/M/P MEMORY DIAGNOSTIC
11/44 CACHE AVAILABLE
CSR MAP
CSR 0 1 2 3 4 5 6 7 8 9 A B C D E F
MEMTYPE P
512K OF MS11-P
512K WORDS OF MEMORY TOTAL
MEMORY CONFIGURATION MAP
16K WORD BANKS
1 2 3 4 5 6 7
012345670123456701234567012345670123456701234567012345670123
ERRORS
INTRLV --------------------------------
MEMTYPE PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPP
CSR 00000000000000000000000000000000
PROTECT PP
END PASS #QV 1 |
ZM9BE0 (Ubi, bootproms)
| Code Block |
|---|
CZM9BE0 M9312/1144 UBI BOOT
DIAG. ROM (E20) (FOR 11-44 UBI: E58)C0
BOOTSTRAP ROM ENTRY POINTS AND DEVICE CODES
LOC. NO DIAG. RUN DIAG. DEVICE CODE
ROM 1(E48) 173004 173006 MS
ROM 2(E49) 173204 173206 DL
PSEUDO POWER-FAIL VECTOR ADR./NEW PC 173024 173052
ROM SEQUENCE IS INCORRECT AS PER INSTALLATION PROCEDURE.
SEQUENCE SHOULD BE:
ROM 1(E48) DL
ROM 2(E49) MS
END PASS
END PASS
END PASS
END PASS
END PASS
END PASS |
DL = RL01
MS = TS04
ZDLDI0 (mfm, slu)
| Code Block |
|---|
CZDLDI0 DL11-W 11/44 MFM SLU
02 DEVICES UNDER TEST
TRAP CATCHER
TEST# ERR PC RCSR OLDPC TRAP ADR
000024 014540 176500 007472 000424
CONSOLE
17777707 014544 |
Second run fails too:
| Code Block |
|---|
CZDLDI0 DL11-W 11/44 MFM SLU
02 DEVICES UNDER TEST
TRAP CATCHER
TEST# ERR PC RCSR OLDPC TRAP ADR
000024 014540 176500 007474 000424
CONSOLE
17777707 014544 |